Definition(s) of PERFORMANCE

How is TECHNICAL SPEED being used - Where did we lost CYCLES?

PERFORMANCE

A machine should be available to reliably at a given speed.

When it is NOT running its theoretical maximum speed:

When and Why was it NOT maximal?

What is

PERFORMANCE

Was the machine running at maximum speed or not?

To calculate the performance rate, the THEORETICAL maximum speed is related to the ACTUAL speed.
The THEORETICAL maximum speed is currently most probably not achievable, just like the theoretical maximum running time will not be achieved.
The goal of the performance rate is to visualize ALL potential, regardless whether it is considered to be ‘realistic’ or achievable.
What IS achievable is not yet discovered; to find out is a task of kaizen teams.
The Theoretical Maximum is based on physical limitations (that cannot be stretched without changing the physics and thus the process), rather than on ‘practical’ or ‘technical’ limits (that can be stretched by kaizen teams).

Time

versus

Quantity

What Unit of Measure to use?

The maximum speed can be calculated in time or in number of product; i.e.
  • maximum speed is 10 seconds per product
  • maximum speed is 6 products per minute

Nevertheless since OEE is primarily a shopfloor tool, and people on the shopfloor usually rather talk about ‘units being produced’ than ‘seconds it has taken to produce a unit’, it is preferred to register speed in units, not in time.

Principles

The parameters for Performance

can be expressed in either TIME or QUANTITY,

  • TIME is needed for correct calculations
  • QUANTITY is preferred for effective communication

Maximum Speed

of What?

The different kinds of Maximum Speed of a machine

The maximum speed can be determined from the NPC, the Name Plate Capacity (Design speed).
However, mostly there are several product(groups) on a machine with their own derived maximum speed. In such cases, special care has to be taken not to include hidden losses in the maximum speed due to ‘difficult products’ which might refer to ‘products which we don’t control the process for’.

NPC

Name Plate Capacity

The correct use of NPC

The NPC should not be taken granted for. More than once it was discovered to include all kind of hidden losses.

The manufacturer might have chosen a low NPC for reasons of liability or to ‘fit’ the equipment with other equipment in a line.

Usually the supplier defines the NPC using a “standard product”.
To what extent this standard product is similar to your own product must be investigated.

Maximum Speed

per product

Maximum Speed of a Product on a Machine

The derivation of different maximum speeds for different products should be done in a mathematical manner.
Example:
An extruder is designed (and checked for!) extruding max. 500 kg plastic per hour.
Product A consists of 250 grams plastic, product B consists of 500 grams. Thus:
  • the theoretical maximum speed for A is 500kg/250gram= 2000 pcs per hour.
  • The theoretical maximum speed for B is 500kg/500gram= 1000 pcs per hour.

 The theoretical maximum speed for a product-machine combination is called ‘The Standard’.

This means that each product group on a certain machine can have its own maximum speed.
Attention: proceed here almost mathematically! A beaker of 250 ml theoretically takes half as long to feel as a beaker of 500 ml.

250 ml strawberry yogurt and 250 ml plum yogurt should therefore have the same maximum speed on a certain system.
If the plum yoghurt is driven more slowly, the maximum speed should not be reduced, but rather be investigated what is slowing down the plum yoghurt!

 The Standard is specifically not called ‘Norm’, since this word has negative associations related to agreed wages for many people in different countries.

How ‘Maximal’ is Maximum Speed?

'Maximal' means: It can IMPOSSIBLY be more...

This statement should be taken serious. If not done so, situations may (and do) occur where the shopfloor is filled with scrap, the machine is suffering one breakdown after the other and still accounts for 80% or more OEE. How?

70% Availability, 80 % Quality, 143% Performance = 80% OEE !

As soon as the performance rate goes over 100% (indicating the standard is chosen too low!) the beautiful balance of the OEE parameters is broken, and the focus may be taken away from what it is all about: identifying and reducing losses.

In cases where the maximum speed has to be determined based upon a Best Of Best analysis, it should be considered that this BOB is achieved under the former and current circumstances, including current losses.

Since in the end even standards are broken by product- and equipment improvement, the BOB should not be considered too easily as maximum value. As a rule of thumb the BOB value should be raised with at least 10 to 25% to serve as Standard.

Principles

The standard is the theoretical maximum speed for a product(group) on the machine;
thus the performance rate never exceeds 100%

This means:

The theoretical maximum capacity of the equipment
And thus it can NEVER be more, so:

At well-chosen Standards, the performance rate will NEVER exceed 100%,
unless the product or the machine fundamentally changes

The goal of OEE is NOT to be close to 100% or to be high at all!
The aim is to have a fixed reference point on the system over the years
in order to be able to see if (and where) you improve.

A low OEE at the beginning is good!
There is a lot of potential for improvement!

Speed of a product-mix

Performance of multiple products with different speeds

In cases where multiple products have been produced (both sequentially
as well as parallel) the performance (as well as the quality) part of the OEE is calculated as a weighted average;
calculated between several expected output ranges.

Answer still not found?

If you checked all the sections in the Academy, yet still not found the answer to your question, ask it here.
To help you best, please be as specific as possible and please understand:
We do not want to reply to anonymous questions.